ATTO Technology Diamond Storage Array VT-Class Manual do Utilizador

FastStream VT 5300Installation and Operation ManualFibre Channel to SCSI Virtual Tape Appliance© 2006 ATTO Technology, Inc. All rights reserved. All b

5ATTO Technology Inc. FastStream VT 5300 Installation and Operation Manual 2.0 InstallationIf you have not already completed the instructions on the

6• The switch(es) allows UDP broadcast messages to be passed through.• A router is not placed between the host running QuickNav and the FastStream VT

7ATTO Technology Inc. FastStream VT 5300 Installation and Operation Manual 2.1 Configure Virtual TapeThe ATTO FastStream VT 5300 allows configuration

8Use quick initial configurationQuick Configuration quickly generates a Virtual Tape Library after you answer a few key questions. The procedure uses

9ATTO Technology Inc. FastStream VT 5300 Installation and Operation Manualare filled in automatically by the FastStream but you may change these param

10Secure data through Write ProtectionFor added security, write protection can be enabled for any tape cartridge with a VTL. When write protection is

11ATTO Technology Inc. FastStream VT 5300 Installation and Operation Manual 2.2 Optional changes to system parametersDefault values are appropriate f

12Exhibit 2.2-1 System Configuration pageAdvanced CLI pageChanges to other parameters may be made using the Advanced page. CAUTIONCAUTIONDo not use t

13ATTO Technology Inc. FastStream VT 5300 Installation and Operation Manual 3.0 Monitor storage and diagnose configurationsYou may determine the perf

14Health and Status Monitor page1 If you are not already in the FastStream GUI, type the IP address of your appliance, as found in Use the FastStream

15ATTO Technology Inc. FastStream VT 5300 Installation and Operation Manualmessage; it cannot respond to a rejection by a server for an invalid addres

16Scan drive surfacesThe read only test performs a non-destructive scan over the entire surface of each drive to identify bad areas of the disk drives

17ATTO Technology Inc. FastStream VT 5300 Installation and Operation Manual 4.0 Modify storageUse the FastStream GUI to replace a failed drive, add n

18Rebuild RAID GroupsIf you receive an E-mail notification from the FastStream VT 5300 as set up previously using the Phone Home error notification (r

19ATTO Technology Inc. FastStream VT 5300 Installation and Operation ManualAdd a VTL from another FastStream VTLIf you want one FastStream VT 5300 to

20Move Virtual Tape CartridgesThe Move Medium page is an interface which simulates a generic library front panel operation. 1 If you are not already i

21ATTO Technology Inc. FastStream VT 5300 Installation and Operation Manual 5.0 Update storage and firmwareYou can update the ATTO FastStream VT 5300

22Use FTP over Ethernet 1 Establish an FTP link to the ATTO FastStream VT 5300 that is to be flashed. 2Use the PUT command to download the firmware. F

23ATTO Technology Inc. FastStream VT 5300 Installation and Operation Manual 6.0 Interface optionsThe best way to manage, monitor and configure the Fa

24NoteIn serial port sessions, there is no prompt on the line below the word Ready. Begin typing commands in the blank line where the cursor is restin

iATTO Technology Inc. FastStream VT 5300 Installation and Operation ManualAppendix A CablingAdditional information to physically connect ports to de

iiAppendix1 Connect the cable from the SCSI device to a VHDCI SCSI port on the FastStream VT 5300.2 Check the type of cable, cable length limit and nu

iiiATTO Technology Inc. FastStream VT 5300 Installation and Operation ManualAppendix B Designing RAID groupsThe ATTO FastStream VT 5300 provides ins

ivAppendixusers with critical data which cannot be lost or corrupted due to the failure of a single drive. With RAID Level 1, the host sees what it be

vATTO Technology Inc. FastStream VT 5300 Installation and Operation ManualAppendix C CLI provides an ASCII-based interfaceThe command line interface

viAppendixCLI error messagesThe following error messages may be returned by the Command line InterfaceERROR. Invalid Command. Type 'Help' fo

viiATTO Technology Inc. FastStream VT 5300 Installation and Operation ManualCLI summary The following chart summarizes the Command Line Interface comm

viiiAppendixExit exitFCConnMode loop set fcconnmode ptpFCDataRate auto get fcdatarate FCHard disabled set fchard disabledFCHardAddress fp1=3; fp2=4set

ixATTO Technology Inc. FastStream VT 5300 Installation and Operation ManualRGHaltConversion rghaltconversion g1RGHaltRebuild rghaltrebuild g1RGMemberA

xAppendixCLI command explanationsCommand Line Interface commands are listed alphabetically with explanations of what they are used for, their defaults

Contents 1.0 ATTO FastStream VT 5300 increases reliability ...1Hardware featuresVirtual Tape featuresBackup and restore feat

xiATTO Technology Inc. FastStream VT 5300 Installation and Operation ManualDefaultInterleave DefaultInterleave assigns or retrieves the system-default

xiiAppendixEmailNotifyAddressConfigures notification addresses using an index (a number between 1 and 5, inclusive), the full E-mail address of the re

xiiiATTO Technology Inc. FastStream VT 5300 Installation and Operation ManualFCDataRateSpecifies the rate the FastStream uses, 1 Gigabit/sec., 2 Gigab

xivAppendixIPDHCPSelecting DHCP allows the FastStream to request an IP address from the network. The network must have at least one DHCP server. Defau

xvATTO Technology Inc. FastStream VT 5300 Installation and Operation ManualRAIDCommandTimeout Specifies in milliseconds the range of time the drives h

xviAppendixRGDisplay Displays status information for a single RAID Group, or if All is used, all available RAID groups. RGDisplay [GroupName | All ] R

xviiATTO Technology Inc. FastStream VT 5300 Installation and Operation ManualRMStatus Displays the status of all RAID Members within the specified RAI

xviiiAppendixSerialPortBaudRateConfigures the baud rate for the unit’s RS-232 serial port. The number of data bits is fixed at 8 with no parity.set Se

xixATTO Technology Inc. FastStream VT 5300 Installation and Operation ManualAppendix D Standards and compliancesThe equipment described in this manu

xxAppendixEuropean StandardsDeclaration of ConformityThis following statement applies to the ATTO FastStream VT 5300. This device has been tested in t

4.0 Modify storage ...17Initialize and verify drivesAdd drives to a RAI

xxiATTO Technology Inc. FastStream VT 5300 Installation and Operation ManualAppendix E Warranty, contact informationManufacturer limited warrantyMan

xxiiAppendix

1ATTO Technology Inc. FastStream VT 5300 Installation and Operation Manual 1.0 ATTO FastStream VT 5300 increases reliabilityThe ATTO FastStream™ Virt

2IntroductionSCSI Tape LibraryATTO iPBridge 27004-Gb FC SwitchPossible storage configurationsEthernetFibre ChannelSCSIembedded ATTO iPBridge1500/1550

3ATTO Technology Inc. FastStream VT 5300 Installation and Operation Manual 1.1 Physical attributesThe ATTO FastStream VT 5300 is a Fibre Channel to

4InstallationA bicolor Ready/Fault LED is lighted green to indicate ready, lighted yellow to show a faulted condition, and off indicates not ready.SCS